Faults and Solutions of Lining Fluorine Pump

Category: Water pump knowledge

2024-08-06

Fluorine pump is a kind of commonly used industrial pump, widely used in chemical, pharmaceutical, environmental protection and other fields. However, due to long-term use or other factors, some failures may occur in the lining fluorine pump. The following will introduce the common fault lining fluorine pump and its solution.

1. common fault of lining fluorine pump

1. Insufficient flow: The flow of the pump is not up to expectations, and deviations in records or actual use may occur. Fluorine-lined pumps may also suffer from flow instability. Unstable flow is usually due to the inlet valve is not fully open, flow parts blockage or pump body leakage and other reasons.

2. Leakage: The sealing performance of the pump is not good, resulting in medium leakage. Fluorine pump may leak. Leakage is usually caused by worn seals, improper installation or severe wear of the pump body.

3. Noise and vibration: abnormal noise and vibration during operation. Lining fluorine pump in the working process may appear noise situation. Noise is usually caused by bearing damage, impeller imbalance or pump body loosening.

4. The pump cannot be started: the motor cannot drive the pump to rotate.

5. The temperature is too high: the temperature of the pump body or motor is too high during operation. The motor of the fluorine-lined pump may overheat. Motor overheating is usually caused by high working environment temperature, heavy motor load or poor ventilation.

2. Solution

1. Insufficient flow:

Check whether the speed of the pump meets the requirements. Inspect the inlet duct for blockage or air leakage. Inspect the pump impeller for damage or wear and replace if necessary. The solution is to check whether the inlet valve is fully opened, clean the circulation parts and ensure its unobstructed, and check whether the seal is intact to prevent the pump body from leaking.

2. Leakage:

Check for worn or damaged seals and replace. Check whether the pump body, flange and other connections are fastened. Check whether the medium contains impurities and filter if necessary. The solution is to check and replace worn seals, ensure that the seals are installed properly, and clean the pump body regularly to reduce wear.

3. Noise and vibration:

Inspect the bearings of the pump for wear or damage. Check whether the base of the pump is stable, and tighten if necessary. Check whether the impeller of the pump is rubbing against the casing, adjust or replace if necessary. Solutions include checking and replacing worn bearings, balancing the impeller, and retightening the pump body to ensure smooth pump operation.

4. Pump fails to start:

Check whether the power is on. Check the motor for damage. Check whether the drive part of the pump is stuck or blocked. Solutions include reducing the working environment temperature, reducing motor load or improving ventilation conditions.

5. The temperature is too high:

Check whether the load of the pump is too large and make appropriate adjustments. Check whether the bearing of the pump is short of oil, add oil or replace the lubricating oil. Check whether the ambient temperature is too high, if necessary, take measures to cool down.

Fluorine-lined pumps may encounter leakage, loud noise, unstable flow and motor overheating during use. For different faults, we can take corresponding solutions, such as replacing seals, bearings, cleaning circulation parts, improving ventilation conditions, etc. Regular inspection and maintenance of the lining fluorine pump to ensure its normal operation is of great significance to ensure the smooth progress of production and work.

The above is just a common lining fluorine pump fault and its solution, the specific situation may vary due to the type of pump, the use of different environments and media. In the actual use process, if you encounter an unsolvable fault, it is recommended to contact a professional for maintenance in time. At the same time, the lining fluorine pump is regularly maintained and maintained to extend its service life and ensure work efficiency.

Previous: Working principle and structure of lining fluorine pump

Next: Removal and installation steps of lining fluorine pump

Contact Us

Free Hotline:+86 18142662779

Fixed telephone:+86 19313001794      

Mobile:+86 18142662779(WeChat/WhatsAPP)

E-mail:info@sanchangpump.net