Removal and installation steps of brine liquid production pump

Category: Water pump knowledge

2024-07-22

Halogen liquid production transfer pumpThe removal and installation steps of are very important and need to be performed carefully. The correct operation can ensure the safe and efficient operation of the equipment, but also to maximize the service life of the pump.

1. removal steps

1. Preliminary preparation: ensure that the power supply has been disconnected, the pressure in the pump has been completely released, and necessary cleaning work has been carried out. Prepare appropriate tools, such as wrenches, screwdrivers, etc. Before disassembling the halogen liquid production transfer pump, it must be ensured that the power supply of the pump is completely cut off and relevant safety measures are taken. Next, the pump needs to be cleaned to ensure that the surface is free of impurities and dirt. Before removal, it is necessary to prepare appropriate tools, such as wrenches, screwdrivers and lubricants.

2. Remove the shell: Use a tool to remove the external fixing screws of the pump and remove the shell. First, open the drain valve of the water injection pump to drain the liquid in the system to avoid accidental leakage. Next, use a wrench or screwdriver to remove the fasteners that fix the pump, and completely disassemble the water injection pump and the pipe connected to it. During this process, the balance of the pump should be carefully maintained to avoid damage or slippage.

3. Remove the bearing: the bearing is usually detachable, use a special tool to loosen the bearing.

4. Disassemble the impeller and shaft seal: gently rotate the impeller and remove it from the shaft after confirming that there is no obstruction. Special care should be taken to avoid damaging the seal face.

5. Check the internal parts: check the internal parts of the pump, such as rotors, bearings, impellers, etc., for wear or damage.

6. Remove the sealing device and other accessories: according to the specific situation, remove other parts such as sealing device, pressure sensor, etc. After the disassembly is completed, the old parts, including seals and blades, need to be inspected in order to replace the parts that need to be repaired or replaced. Then, according to the type and specifications of the water injection pump, select the appropriate new parts for replacement. When installing new accessories, ensure that they are properly connected and tightened to prevent leakage.

2. installation steps

1. Pre-preparation: Ensure that all parts are cleaned and check for damage or wear. Prepare the necessary tools and installation materials.

2. Install the bearing and impeller: first install the bearing to ensure that the bearing position is correct and fixed firmly. Then install the impeller, ensuring that the impeller fits tightly with the shaft.

3. Install the shaft seal: When installing the shaft seal, ensure that the sealing surface is clean and the seal is installed correctly to avoid leakage.

4. Install the shell: Place the shell on the pump body and make sure that all screw holes are aligned, and then fix the screws.

5. Install the sealing device and other accessories: install other parts in the reverse order of disassembly, such as sealing device, pressure sensor, etc.

6. Check and test: After the installation is completed, check whether the pump is installed correctly, and then conduct a trial run to ensure that the pump runs normally and there is no leakage.

7. Maintenance: regular maintenance, check the operation of the pump, if found abnormal should be handled in time. Regularly clean and lubricate the pump to ensure long-term stable operation of the pump.

Note:

1. In the process of operation, be sure to follow the safety operation procedures to ensure personal safety.

2. During disassembly and installation, pay attention to protect the parts of the pump to avoid damage.

3. For uncertain parts or difficult to operate steps, it is recommended to consult professionals or manufacturers.

The above are the disassembly and installation steps of the halogen liquid production and delivery pump. Correct operation can ensure the normal operation of the pump and prolong its service life. The disassembly and installation steps of the halogen liquid production and delivery pump are a detailed and complicated process, and the correct operation process needs to be followed. Only by ensuring that each step is strictly implemented can the safe and efficient operation of the pump be ensured and the efficiency of the entire oilfield water injection system be improved.

Previous: Construction industry multi-stage pump selection factors

Next: Guide to repair and maintenance of brine liquid production transfer pumps

Contact Us

Free Hotline:+86 18142662779

Fixed telephone:+86 19313001794      

Mobile:+86 18142662779(WeChat/WhatsAPP)

E-mail:info@sanchangpump.net