Causes and Preventive Measures of Water Pump Not

Category: Water pump knowledge

2024-05-28

The reason why the water pump is not filled with water may involve many aspects such as power supply, water inlet, pump body interior and pipeline. Users should check one by one according to the actual situation and take corresponding solutions. At the same time, strengthen preventive measures to ensure the normal operation of the pump and provide a stable water source for life and production.

Water pump, as an important equipment of water transportation, is widely used in many fields such as industry, agriculture and family. However, in actual use, the water pump occasionally does not take water, which brings many troubles to users. This article will deeply discuss the reasons why the pump does not take water, and propose corresponding solutions to help users better use and maintain the pump.

1. Preventive measures

In order to avoid the problem of water pump, users can take the following precautions:

Regular maintenance: regular maintenance of the pump, including cleaning the water inlet, checking the power supply and pipes, etc., to ensure that the pump is in good working condition.

Correct use: When using the water pump, you should follow the operating procedures to avoid long-term overload operation to avoid damage to the internal parts of the water pump.

Choose high-quality products: When purchasing a water pump, you should choose products with reliable quality and stable performance to reduce the probability of water pump failure.

2. The reason why the water pump is not filled with water

Power supply problem: The power supply of the water pump is unstable or the voltage is too low, which may cause the water pump to fail to work normally and thus cannot be supplied with water.

The water inlet is blocked: If the water inlet of the water pump is blocked by debris, the water cannot enter the pump body smoothly, resulting in the water pump cannot be supplied.

Internal failure of the pump body: the impeller, bearing and other parts of the pump are damaged or worn, which will affect the pumping capacity of the pump and cause no water supply.

Pipeline problems: water leakage, rupture or blockage of the pipeline connected to the water pump may also cause the water pump to fail.

3, the water pump does not fill the solution

Check the power supply: first check whether the power supply of the water pump is stable and whether the voltage is normal. If there is any problem, contact the power department for maintenance or adjustment in time.

Clean the water inlet: turn off the power of the water pump, disassemble the filter screen at the water inlet of the water pump, and clean up the blocked debris. After cleaning, reinstall the filter and start the pump.

Repair the pump body: if the internal parts of the pump are damaged or worn, professionals should be invited to disassemble, repair or replace the damaged parts of the pump. After the repair is completed, reassemble and test the pump performance.

Check the pipeline: Check whether the pipeline connected to the pump is leaking, cracked or blocked. If there is any problem, the pipeline should be repaired or replaced in time. At the same time, ensure that the pipeline connection is firm to avoid water leakage.

4. Precautions for use of water pump

Before the pump is put into use, it needs to be put into trial operation, and then put into use after its working condition reaches the use requirements. In fact, this test run is the same as the normal operation, that is, the preparatory work is done first, and the safety operation procedures are strictly installed to operate.

When the water pump is in use, it is necessary to pay attention to the temperature of the bearing, which should not be too high, and the oil level in its bracket should be between the scales. If in the process of use, leakage and other abnormal phenomena, then you must immediately stop using, such as troubleshooting before use.

When the water pump is used, after it stops, the pressure gauge should be turned off first, and then the throttle valve above the water outlet pipe one by one. When the motor enters the light load state, the vacuum gauge should be turned off. Finally, the water pump can be stopped and the water in the suction pipe can be raised.

Previous: What is the difference between single-stage pump and double-suction pump

Next: Causes and solutions of water pump failure

Contact Us

Free Hotline:+86 18142662779

Fixed telephone:+86 19313001794      

Mobile:+86 18142662779(WeChat/WhatsAPP)

E-mail:info@sanchangpump.net